Hyundai Tucson: Passenger Air Bag (PAB)
Components Location
- Passenger Air Bag (PAB)
Removal
- Set the front tires straight-ahead.
- Disconnect the batteiy negative terminal.
WARNING
After disconnecting the cables, wait at least 3 minutes.
- Remove the glove box.
(Refer to Body (Interior and Exterior) - "Glove Box")
- Remove the passenger airbag mounting nuts (A).
- Disconnect the passenger airbag connectors (A).
- Remove the main crash pad assembly.
(Refer to Body - "Main Crash Pad Assembly")
WARNING
Replace the crash pad which is damaged while PAB is deployed.
- Remove the passenger airbag (A) from the crash pad after loosening the mounting bolts.
Installation
- Disconnect the batteiy negative cable from batteiy and wait for at least three minutes before beginning work.
- Place a passenger airbag oil the crash pad and tighten the passenger airbag mounting bolts (A).
Tightening torque : 3.9 - 5.9 N.m (0.4 - 0.6 kgf.m. 2.9 - 4.4 lb-ft)
- Install the main crash pad assembly.
(Refer to Body - "Main Crash Pad Assembly")
- Connect the passenger airbag connectors (A).
- Tighten the passenger airbag mounting nuts (A).
Tightening torque : 3.9 - 5.9 N.m (0.4 - 0.6 kgf.m. 2.9 - 4.4 lb-ft)
- Install the glove box.
(Refer to Body (Interior and Exterior) - "Glove Box")
- Reconnect the batteiy cable (-).
- After installing the airbag module, confirm proper system operation.
WARNING
Switch ON the ignition. The SRS indicator light should turn on for about three-six seconds and then off.
Description
The Side Airbags (SAB) are installed inside the front seat and protects the driver and passenger from danger when side crash occurs. The SRSCM determines deployment of side airbag by using Side Impact Sensor (SIS) signal.
WARNING
Never attempt to measure the circuit resistance of the airbag module (squib) even if you are using the specified tester. If the circuit resistance is measured with a tester, accidental airbag deployment will result in serious personal injury.
READ NEXT:
Side airbag (SAB)
Components Location
Side airbag (SAB)
Removal
Disconnect the batteiy negative terminal.
WARNING
After disconnecting the cables, wait at least 3 minutes.
Remove the front seat back cover.
(Refer to Body - "Front Seat Back
Curtain Air Bag (CAB)
Components Location
Curtain Air Bag (CAB)
Removal
Disconnect the batteiy negative terminal.
WARNING
After disconnecting the cables, wait at least 3 minutes.
Remove the roof trim.
(Refer to Body - "Roof Trim Assembly"
Center side airbag (CSAB)
Components Location
Center side airbag (CSAB)
Removal
Disconnect the batteiy negative terminal.
WARNING
After disconnecting the cables, wait at least 3 minutes.
Remove the front seat back cover.
(Refer to Body - "Front S
SEE MORE:
Troubleshooting
Trouble Symptom
Coolant
leakage
From the
bleed hole of
the water
pump
From gaskets
or bolts
From outer
surface of
water pump
Probable Cause
Visually
check
Check leaks
after about
ten-minute
warming up.
If co
Lane Keeping Assist Settings
Setting features
Lane Safety
With the engine on, select 'Driver
Assistance → Lane Safety' from the
Settings menu to set whether or not to
use each function.
If 'Assist' is selected, Lane Keeping
Assist will automatically assist the
d
Information
- Home
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Owner's Manual
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual