TucsonDataManu

.com

Hyundai Tucson: Head Lamp Aiming

Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual / Body Electrical System / Lighting System / Head Lamp Aiming

Instructions

Alternately turn the adjusting gear to adjust the head lamp aiming.

If beam-setting equipment is not available, proceed as follows:

  1. Draw vertical lines (Vertical lines passing through respective head lamp centers) and a horizontal line (Horizontal line passing through center of head lamps) on the screen.
  2. The vehicle should be placed on a flat ground.
  3. With the head lamp and battery in normal condition, aim the head lamps so the brightest portion falls on the horizontal and vertical lines.
  1. Horizontal (High beam / Low beam)
  2. Vertical (High beam / Low beam)

Things to check before headlamp aiming

Things to check before headlamp aiming

  1. Measure condition

1 )Measurements shall be carried out on a vehicle which has travelled a distance of between 1.000 km and 10.000 km, preferably 5.000 km.

2)Tire shall be inflated to the full-load pressure specified by the vehicle manufacturer. The vehicle shall be fully replenished (fuel, water, oil) and equipped with all accessories and tools specified by the manufacturer. Full fuel replenishment means that the fuel tank shall be filled to not less than 90% of its capacity.

3)The vehicle shall have the parking brake released and the gearbox in neutral.

4)The vehicle shall be conditioned for at least 8h at the temperature between 10~30ºC.

5) If a photometric or visual method is used, headlamps with a well-defined dipped-beam cut-off should preferably be installed on the vehicle under test in order to facilitate the measurements. Other means are allowed to obtain a more precise reading (for ex.

removal of the headlamp lens)

6)If the vehicle is fitted with a manual leveling device, it shall be '0' position.

  1. Vehicle preparation

1)If a visual inspection of the dipped-beam pattern on the screen or a photometric method is used, measurement shall be carried out in a dark environment of sufficient area to allow the vehicle and the screen to be placed. Headlamp center of reference shall be at a distance from the screen of at least 10 m.(In case of In-line, it is set within lm but it converts to 10m and recognizes cut-off)

2)The ground on which measurements are made shall be as flat and horizontal as possible, so that the reproducibility of measurements of dipped-beam inclination can be assured with an accuracy of 0.5 mrad (+-0.05 %).

3) If a screen is used, its marking, position and orientation in relation to the ground and to the median longitudinal plane of the vehicle, shall be such that the reproducibility of the measurement of the dipped-beam inclination can be assured with an accuracy of 0.5 mrad (+-0.05 %).

4)During measurements, the ambient temperature shall be between 10~30ºC.

Head Lamp And Fog Lamp Aiming Point

Head Lamp And Fog Lamp Aiming Point

(Low beam : H1,W1 / High beam : H2,W2) (Unit: mm)

  1. Head Lamp (Low beam)
  • With the low beam turned on, adjust the cut-off line to be located as shown in the picture below.
  • If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

  1. Head Lamp (High Beam)
  • Turn the high beam on without driver aboard.
  • The cut-offline should be projected in the cut-offline shown in the picture.
  • When aiming the low beam, vertical aiming shuld be adjusted after adjusting the horizontal aiming.
  • If head lamp leveling device is equipped, adjust the head lamp leveling device switch with 0 positions.

Head lamp fogging

Head lamp fogging

Check the below instruction procedure when the head lamp is fogged.

Outside Rear View Mirror - Removal

    READ NEXT:

     Outside Rear View Mirror - Removal

    Removal When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. Put on gloves to prevent hand injuries. Disconnect the negative (-) battery terminal. Remove the f

     Outside Rear View Mirror - Installation

    Outside Rear View Mirror Installation Install the outside rear view mirror and connect the connector. Tightening torque : 6.9 - 10.8 N.m (0.7 - 1.1 kgf.m, 5.0 - 8.0 lb-ft) Connect the negative (-) batteiy terminal. Front/Rear Turn Sig

     Rear Outside Combination Lamp

    Disconnect the negative (-) battery terminal. Loosen the mounting bolts then remove the outside rear combination lamp (A). Disconnect the rear combination lamp connector (A). Remove the bulb after turning it in the counter

    SEE MORE:

     Clutch Master Cylinder

    Components Clutch pedal arm Clutch master cylinder Clutch pedal assembly Removal Remove the clutch pedal. (Refer to Clutch System - "Clutch Pedal") Remove the clip (A). Remove the push rod pin (A) by push

     Front Brake Disc

     Front Brake Disc Thickness Check Inspection Check the brake pads for wear and fade. Check the brake disc for damage and cracks. Remove all rust and contamination from the surface, and measure the disc thickness at 24 points, at leas

    Information