Hyundai Tucson: Rear door latch
Component Location
- Rear door latch
Replacement
WARNING
- When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.
- Put on gloves to prevent hand injuries.
- Remove the rear door window glass.
(Refer to Rear Door - "Rear Door Window Glass")
- Remove the rear door outside handle.
(Refer to Rear Door - "Rear Door Outside Handle")
- Loosen the mounting nuts and bolt, remove the rear door channel (A).
Tighten torque :
Bolt: 6.9 - 10.8 N.m (0.7 - l.lkgf.m, 5.1 - 8.0 lb-ft)
Nut: 3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.3 lb-ft)
- Loosen the rear door latch mounting screws (A).
Tightening torque : 7.8 - 14.7 N.m (0.8 - 1.5 kgf.m, 5.8 - 10.8 lb-ft)
- Loosen the mounting screw, remove the rear door latch assembly (A).
- Disconnect the rear door latch connector (A).
- Disconnect the lock pin (A) in the direction of the arrow and then separate the locking pin (A) and connecting rod (B).
- Press the lock pin, remove the front door outside handle base (A).
WARNING
- Rear door outside handle base (A).
- Rear door latch (B).
- To install, reverse the removal procedure.
WARNING
- Replace any damaged clips (or pin - type retainers).
- Make sure the door locks and opens properly.
- Make sure the connector is connected properly.
Replacement
- Remove the rear door window glass.
(Refer to Rear Door - "Rear Door Window Glass")
- Loosen the mounting clips, nuts, screws and remove the front wheel guard (A).
- Loosen the mounting nuts, remove the front door power window regulator (A).
Tightening torque : 3.9 - 5.9 N.m (0.4 - 0.6 kgf.m, 2.9 - 4.4 lb-ft)
- To install, reverse the removal procedure.
WARNING
- Make sure connectors are connected properly and each rod is connected securely.
- Make sure the door locks / unlocks and opens / closes properly.
READ NEXT:
Body Side Molding
Replacement
WARNING
When removing with a flat-tip screwdriver or remover, wrap
protective tape around the tools to prevent
damage to components.
Put on gloves to prevent hand injuries.
Remove the roof trim.
(Refer to Roof Trim - &
Rear Spoiler
Component Location
Rear Spoiler
Replacement
WARNING
When removing with a flat-tip screwdriver or remover, wrap
protective tape around the tools to prevent
damage to components.
Put on gloves to prevent hand injuries.
Remo
Tailgate back panel
Component Location
Tailgate back panel
Replacement
WARNING
Put on gloves to prevent hand injuries.
WARNING
Take care not to scratch the tailgate and body surface.
Remove the tailgate lower trim.
(Refer to Tail Gate - "Tail G
SEE MORE:
Cooling Fan Assembly
Components
Cooling fan
Fan motor
Cooling fan shroud
Cooling Fan Assembly
Disconnect the negative battery terminal.
Remove the radiator.
(Refer to Cooling System - "Radiator")
Remove the cooling fan (A) from the rad
Rear Brake Pad
After installing the rear caliper, perform "Brake Pad Replacement Mode"
using the self-diagnosis. EPB Apply
Select C2 (Release) on the screen below.
After disassembling/assembling the caliper body or replacing
Information
- Home
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Owner's Manual
- Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual