TucsonDataManu

.com

Hyundai Tucson: Rear Brake Caliper

Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual / Brake System / Braking System - operation and description / Rear Brake Caliper

Components

  1. EPB Actuator
  2. Caliper body
  3. Caliper carrier
  4. Pad retainer
  5. Brake pad

Removal

  1. Before removing the rear caliper, perform "Brake Pad Replacement Mode" using the self-diagnosis.

    Raise the vehicle, and make sure it is securely supported.

  • EPB Apply : Release the EPB, push the EPB switch or using self-diagnosis.

  1. Select C2 (Release) on the screen below.

  • EPB None Apply : Release the parking brake pedal and parking brake cable is loose.
  1. Turn ignition switch OFF and disconnect the negative (-) battery cable.
  2. Loosen the wheel nuts slightly.

Raise the vehicle, and make sure it is securely supported.

  1. Remove the rear wheel and tire (A) from the rear hub.

Tightening torque : 107.9 - 127.5 N.m (11.0- 13.0 kgf.m, 79.6 - 94.0 lb-ft)

WARNING

Be careful not to damage the hub bolts when removing the rear wheel and tire (A).

  1. Disconnect the EPB connector or parking brake cable.
  • EPB Apply : Disconnect the EPB connector (A).

  • EPB None Apply : Remove the parking brake cable (A), after removing the clip.

  1. Remove the hose after loosening the brake hose bolt (A) from the caliper.

Tightening torque : 24.5 - 29.4 N.m (2.5 - 3.0 kgf.m, 18.1-21.7 lb-ft)

  1. Remove the guide rod bolt and then pivot the caliper body (A) up out of the way.

Tightening torque : 21.6-31.4 N.m (2.2-3.2 kgf.m. 15.9-23.1 l b - f t )

  1. Remove the brake pad (A).

  1. Remove the pad liner (A).

  1. Remove the brake caliper body (A) by loosening the upper bolt of the brake caliper guide.

  1. Remove the caliper carrier (A) after loosening the caliper mounting bolt.

Tighteuiug torque : 78.5 - 98.1 N.m (8.0 - 10.0 kgf.m. 57.9 - 72.3 lb-ft)

  1. Remove the rear brake disc (A) after loosening the screw.

Tightening torque : 4.9 - 5.9 N.m (0.5 - 0.6 kgf.m. 3.6 - 4.3 lb-ft)

Rear Brake Disc

    READ NEXT:

     Rear Brake Disc

    Rear Brake Disc  Thickness Check Inspection Check the brake disc for damage and cracks. Remove all rust and contamination from the surface, and measure the disc thickness at 24 points, at least, of same distance (5mm) from the brake

     Front Brake Pad

    Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. Remove the front wheel and tire (A) from front hub WARNING Be careful not to damage the hub bolts when removing the front wheel and tire (A).

     Rear Brake Pad

    After installing the rear caliper, perform "Brake Pad Replacement Mode" using the self-diagnosis. EPB Apply Select C2 (Release) on the screen below. After disassembling/assembling the caliper body or replacing

    SEE MORE:

     Airbag Disposal

    When you scrap a vehicle equipped with an airbag, you must deploy it first. When you deploy an airbag, you need to have a skilled mechanic do the work. The used airbag should not be reinstalled in another vehicle for reuse. WARNING Upon de

     LCD display control

    The LCD display modes can be changed by using the control buttons. MODE button for changing modes MOVE switch for changing items SELECT/RESET button for setting or resetting the selected item Information When the infotainment system

    Information