TucsonDataManu

.com

Hyundai Tucson: IMT System Actuator- Removal

Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual / Intelligent Manual Transaxle (IMT) System / IMT System Actuator / IMT System Actuator- Removal

In case of transaxle separated from the vehicle

  1. Remove the Intelligent Manual Transaxle (IMT).

(Refer to Intelligent Manual Transaxle (IMT) System (M6CF3-le) - "Intelligent Manual Transaxle (IMT)")

  1. Pull the clip (A).

  1. Loosen the bolts and then removing the concentric slave cylinder (A).

  1. Loosen the bolts and then removing the IMT system actuator (A).

WARNING

WARNING

  • All of the pin have to be assembled in original placement right after disassembly.
  • If the clutch tube is twisted and bended strongly for disassembling, the rubber caps and the quick connectors can be damaged.
  • The rubber caps can be tilted when the clutch tube has been disassembled with wrong condition (twisted or bended). If the rubber cap have been lost right after disassembly, the
  • If the rubber cap have been lost right after disassembly, the rubber cap can be found in the female connector of the CSC or the IMT system actuator assembly. In this case, rubber caps have to eliminated from the CSC and the IMT system actuator assembly.

In case of transaxle mounted on the vehicle

  1. Remove the air cleaner assembly and the air duct.

(Refer to Engine Mechanical System - "Air Cleaner")

  1. Disconnect the gear position sensor connector (A) and then separate the wiring clip (B).

  1. Loosen the bolt and then separate the wiring bracket (A) after disconnect the IMT system actuator connector (B).

  1. Loosen the bolt and then removing the ground line (A).

Tightening torque : 19.6 - 26.5 N m (2.0 - 2.7 kgfrn, 14.5 - 19.5 lb ft)

  1. Remove the IMT system actuator assembly bolts (A).

Tightening torque : 19.6 - 26.5 N m (2.0 - 2.7 kgfrn, 14.5 - 19.5 lb ft)

  1. Pull the snap pin (A) and then removing the IMT system actuator (B) and clutch tube at the same time.

IMT System Actuator- Installation

    READ NEXT:

     IMT System Actuator- Installation

    Installation Install the IMT system actuator (A) and then tightening the bolts. Tightening torque: 19.6 - 26.5 N.m (2.0 - 2.7 kgf.m. 14.5 - 19.5 lb-ft) Lightly install the concentric slave cylinder (B) on the input shaft (A).

     Gear Position Sensor

    Components and Components Location Gear position sensor Connector and Terminal Information Removal Remove the IMT system actuator. (Refer to Intelligent Manual Transaxle (IMT) Control System - "IMT System Actuator&qu

     Speed Sensor

    Components and Components Location Control shaft complete Description Component location : Control shaft complete is mounted on the top of the manual transaxle, and select & shift cable are equipped. Function : Change the ge

    SEE MORE:

     48V Battery System - Removal

    Turn the ignition switch OFF and disconnect the battery (-) terminal. Remove the luggage board (A). Disconnect the BMS ECU extension wiring harness connector (A). Disconnect the inverter power cables (A). Tightening torque

      Concentric Slave Cylinder Assembly- Adjustment

    Gasoline 1.6 T-GDI Turn ignition switch OFF and disconnect the negative (-) battery cable. Remove the air cleaner assembly and air duct. (Refer to In case by Gasoline 1.6 T-GDI System - "Air Cleaner") After disconnecting a cap

    Information