TucsonDataManu

.com

Hyundai Tucson: IMT System Actuator- Replacement

Hyundai Tucson - Fourth generation (NX4) - (2020-2023) - Workshop Manual / Intelligent Manual Transaxle (IMT) System / IMT System Actuator / IMT System Actuator- Replacement

iMT system actuator fluid - when fluid suction tool is available

  1. Remove the air cleaner assembly and the air duct.

(Refer to Engine Mechanical System - "Air Cleaner")

  1. Remove the reservoir cap (A) and drain the imt system actuator fluid (B).

  1. Fill a new IMT system actuator fluid up to the MAX mark.

Recommended :

  • DOT-LV4 (Recommended), DOT-4 or DOT-3
  • Recommended fluid : SAE J1704 DOT-4 LV, IS04925 CLASS-6
  • Useable fluid : FMVSS116 DOT-4, FMVSS116 DOT-3
  1. Perform the IMT filling check by using the diagnostic tool.

Refer to IMT(intelligent Manual Transaxle) Control System - "IMT System Learning Procedures")

iMT system actuator fluid - when fluid suction tool is unavailable

  1. Remove the air cleaner assembly and the air duct.
  2. Remove the IMT system actuator assembly with combined the clutch tube.

(Refer to Intelligent Manual Transaxle (IMT) Control System - "IMT System Actuator")

  1. Remove the reservoir cap (A) and invert the IMT system actuator assembly.

WARNING

WARNING

Do not remove the pin (A) from the clutch actuator assembly

  1. Keep the actuator (A) inverting until stopping brake fluid flowing out.

  1. Install the IMT system actuator assembly.

(Refer to Intelligent Manual Transaxle (IMT) Control System - "IMT System Actuator")

  1. Fill a new IMT system actuator fluid up to the MAX mark.

Recommended :

  • DOT-LV4 (Recommended), DOT-4 or DOT-3
  • Recommended fluid : SAE J1704 DOT-4 LV, IS04925 CLASS-6
  • Useable fluid : FMVSS116 DOT-4, FMVSS116 DOT-3
  1. Perform the IMT filling check by using the diagnostic tool.

(Refer to Intelligent Manual Transaxle (IMT) Control System - "IMT System Learning Procedures")

    READ NEXT:

     IMT System Actuator- Inspection

    IMT system clutch tube and line Remove the air cleaner assembly and the air duct. (Refer to Engine Mechanical System - "Air Cleaner") Check conditions (disassembled, damaged) of the clutch tube (A) and check leakages of the co

     IMT System Actuator- Removal

    In case of transaxle separated from the vehicle Remove the Intelligent Manual Transaxle (IMT). (Refer to Intelligent Manual Transaxle (IMT) System (M6CF3-le) - "Intelligent Manual Transaxle (IMT)") Pull the clip (A).

     IMT System Actuator- Installation

    Installation Install the IMT system actuator (A) and then tightening the bolts. Tightening torque: 19.6 - 26.5 N.m (2.0 - 2.7 kgf.m. 14.5 - 19.5 lb-ft) Lightly install the concentric slave cylinder (B) on the input shaft (A).

    SEE MORE:

     On vehicle inspection

    Inspection Accelerate the engine to about 3,000 rpm 3 times or more.  Remove the spark plug. (Refer to Spark Plug - "Removal") Check the spark plug visually. If the electrode is dry, the spark plug is normal. If the

     Floor Console - SBC type

    SBC type Floor console assembly SBC type WARNING When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components. Put on gloves to prevent hand injuries. WARNING Tak

    Information

    2022-2026 © - www.tucsondatamanu.com